|
Click here for a sequential list of British Rail catalogue part numbers |
|
Top Die Holder |
|
Top Die |
|
Bottom Die |
|
Retaining Pin |
|
Hose Connector |
|
Tooling |
|
35-ton Press
For use with Tranect HV and UHV terminals |
|
© 2008 TRANECT Ltd |
|
Heavy Duty tools
For use with TK-R and TK-RF terminals |
|
DKB0760 for TK-R terminals 0.75 to 6mm˛ · Die nests are distinctly marked · Adjustable if changes occur, ie. After many crimps · Ratchet mechanism to ensure full crimp closure · Emergency release to interrupt crimping operation · Unique design makes the tool compact and handy · Minimum physical force required |
|
T2258 for TK-R and TK-RF terminals 4.0 to 16mm˛ · Die nests are distinctly marked · Adjustable if changes occur, ie. After many crimps · Ratchet mechanism to ensure full crimp closure · Emergency release to interrupt crimping operation · Unique design makes the tool compact and handy · Minimum physical force required |
|
· System V250 for TK-R and TK-RF terminals 10-300 mm˛ · Equipped with oil spray safety protection cap · Working pressure 630 bar · Crimp force 25 ton · Can also be used with aluminium ‘AK’ crimps up to 800mm˛
|
|
Die Holder V2506 |
|
Die Holder V2508 |
|
B-type die |
|
DUAL SYSTEM for crimping flexible conductors in TK-RF terminals 16mm˛ - 300mm˛ |
|
Crimp head with DUAL CRIMP technique, which starts with an optimised hexagonal crimp and then makes a small indent in the same crimp cycle. This secondary indent further improves gas tightness and well as the electrical and mechanical properties of the crimp connection. |
|
DV1300 Dual Crimp head · Dual dies are available for 16 - 300 mm˛ · No Die holders are necessary when using DUAL dies. · Conventional dies for the DV1300 can be used without the dual function. · The DV1300 can also be used with regular crimp dies for the 1300 system. · Can be used with footpump or battery / mains powered pump |
|
DV1300C Dual Crimp head · Dual dies are available for 16 - 300 mm˛ · No Die holders are necessary when using DUAL dies. · Conventional dies for the DV1300C can be used without the dual function. · The DV1300C can also be used with regular crimp dies for the 1300C system. · Can be used with footpump or battery / mains powered pump |
|
DSA0115 crimp tool for pre-insulated terminals 0,14 - 2.5 mm˛ · Laser marked die nests · Ratchet mechanism ensures fully closed crimps · Emergency release to interrupt crimp sequence · Compact and handy design · Minimum operating force required |
|
ESA0760 and ESA 0760C ‘Miniforce’ crimp tools for symmetrical crimping or pre insulated terminals 0.5 - 6mm˛
· Locator to hold the terminal in the correct position when crimping, to simplify installation · Easy die calibration with die gauge · Die nests leave an imprint to show identification of correct tool used. |
|
ESA0760 |
|
ESA0760C |
|
T2258 |
|
DKB0760 |
|
DSA0115 |
|
V250 crimp head |
|
DV 1300 crimp head |
|
DV1300 dies |
|
DV1300C crimp head |
|
DV1300 dies |
|
Punch and Matrix · For indent crimping of Aluminium AK terminals, no punch holder is required · When indent crimping aluminium terminals, two indents are always required |
|
Matrix |
|
Matrix holder |
|
Punch |
|
Crimp sequence |
|