Tranect 35 ton press |
|
|
|
|
|
|
 |
|
Tranect 35 Ton hydraulic crimping press is supplied with:
- top die holder
- bottom die holder
- hydraulic coupler
- hydraulic hose
- hydraulic pump - choice of either electric or compressed air powered.
- Tranect 35 Ton hydraulic crimping press is recommended for use with Tranect dies to crimp Tranect terminals.
- Each press is stamped with the initials of the technician who assembled it, along with a date code - allowing total traceability.
- All presses are supplied with a two year back to base warranty.
- We service and recondition old hydraulic crimping presses.
- We can also supply a heavy duty hydraulic cable cutter for cutting up to 400 mm² cable.
|
|
| Item |
BR Cat No |
TRANECT No |
Item |
BR Cat No |
TRANECT No |
| Hydraulic press |
39/008318 |
R/35P |
Die Q |
39/008184 |
Die Q |
| Pump, air operated |
39/008323 |
LAHP |
Die R |
39/008186 |
Die R |
| Die H |
39/014511 |
Die H |
Hose+connectors - 2 mtrs |
39/008238 |
BO/500/2 |
| Die I |
39/014512 |
Die I |
Hose+connectors - 3 mtrs |
39/008239 |
BO/500/3 |
| Die J |
39/008177 |
Die J |
Hose connector - female |
39/008098 |
BO/127 |
| Die K |
39/008178 |
Die K |
Hose connector - male |
39/008099 |
BO/128 |
| Die L |
39/008179 |
Die L |
Top die holder |
39/008233 |
TOPDH/R/35P |
| Die M |
39/008180 |
Die M |
Bottom die holder |
39/008228 |
BTMDH/R/35P |
| Die N |
39/008181 |
Die N |
Go Gauge plate F to K |
39/029061 |
TA13209 |
| Die 0 |
39/008182 |
Die 0 |
Go Gauge plate L to O |
39/029063 |
TA13210 |
| Die P |
39/008183 |
Die P |
Go Gauge plate P to R |
39/029065 |
TA13211 |
|
|
|
Dies and Gauges |
|
 |
There is a crimp die for each size of standard terminal. Each crimp die is engraved with the crimp size code letter: F,G,H,I,J,K,L,M,N,O,P,Q,R and R
There is a separate range of crimp dies for the insulation grip terminals: K-X,M-X,N-X,O-X
Operating instructions are available based on British Rail WOSS 560/4.
The crimp die is held in the die holder with a split pin.
|
|
For crimp size:
“F” to “K” use gauge TA13209
“L” to “O” use gauge TA13210
“P” to “R” use gauge TA13211
““K-X” to “O-X” use gauge TA13213 Calibration certificates can be provided if required.
|
|
Hand Tools |
For use with KRF terminals |
|
|
|
|
|
|
DKB0760 for TK-R terminals 0.75 to 6mm²
- Die nests are distinctly marked
- Adjustable if changes occur, ie. After many crimps
- Ratchet mechanism to ensure full crimp closure
- Emergency release to interrupt crimping operation
- Unique design makes the tool compact and handy
- Minimum physical force required
|
T2258 for TK-R and TK-RF terminals 4.0 to 16mm²
- Die nests are distinctly marked
- Adjustable if changes occur, ie. After many crimps
- Ratchet mechanism to ensure full crimp closure
- Emergency release to interrupt crimping operation
- Unique design makes the tool compact and handy
- Minimum physical force required
|
DSA0115 crimp tool for pre-insulated terminals 0,14 - 2.5 mm²
- Laser marked die nests
- Ratchet mechanism ensures fully closed crimps
- Emergency release to interrupt crimp sequence
- Compact and handy design
- Minimum operating force required
|
ESA0760 and ESA 0760C
- Miniforce crimp tools for symmetrical crimping or pre insulated terminals 0.5 - 6mm².
- Locator to hold the terminal in the correct position when crimping, to simplify installation
- Easy die calibration with die gauge
- Die nests leave an imprint to show identification of correct tool used.
|
|
System V250 |
|
|
 |
 |
|
|
|
|
|
|
|
|
|
| System V250 |
| CSA mm² |
Die Holder |
Die Holder |
Die Type |
| 10 |
V2506 |
V2508 |
B8 |
| 16 |
V2506 |
V2508 |
B9 |
| 25 |
V2506 |
V2508 |
B11 |
| 35 |
V2506 |
V2508 |
B13 |
| 50 |
V2506 |
V2508 |
B14.5 |
| 70 |
V2506 |
V2508 |
B17 |
| 95 |
V2506 |
V2508 |
B20 |
| 120 |
V2506 |
V2508 |
B22 |
| 150 |
V2506 |
V2508 |
B25 |
| 185 |
V2506 |
V2508 |
B27 |
| 240 |
V2506 |
V2508 |
B30 |
| 300 |
V2506 |
V2508 |
B32 |
|
|
|
| |
|
|
|
|
|
|
System V250 for TK-R and TK-RF terminals 10-300 mm²
- Equipped with oil spray safety protection cap
- Working pressure 630 bar
- Crimp force 25 ton
- Can also be used with aluminium ‘AK’ crimps up to 800mm
|
|
|
|
|
|
|
|
| |
|
| Accessories for crimping Aluminium with V250 |
| Stranded mm² |
Solid mm² |
Matrix |
Matrix
holder |
Punch |
| 16 |
16 (+25) |
P13M |
V2521 |
P13D |
| 25 |
35 |
P13M |
V2521 |
P13D |
| 35 |
50 |
P20M |
V2521 |
P20D |
| 50 |
70 |
P20M |
V2521 |
P20D |
| 70 |
95 |
P20M |
V2521 |
P20D |
| 95 |
120 |
P25M |
V2521 |
P25D |
| 120 |
150 |
P25M |
V2521 |
P25D |
| 150 |
185 |
P25M |
V2521 |
P25D |
| 185 |
240 |
P32M |
V2531 |
P32D |
| 240 |
|
P32M |
V2531 |
P32D |
| 300 |
|
P32M |
V2531 |
P36/40/44D |
| 400 |
|
P40M |
V2531 |
P36/40/44D |
| 500* |
|
P44M |
V2531 |
P36/40/44D |
| 500** |
|
P2552M |
V2531 |
P2552D |
| 630 |
|
P2552M |
V2531 |
P2552D |
|
 |
 |
|
|
Matrix and punch for V250 |
Crimp sequence for crimping aluminium. |
|
|
| |
|
|
|
DUAL SYSTEM |
or flexible cables in TK-RF terminals |
|
 |
 |
 |
Crimp head with DUAL CRIMP technique, which starts with an optimised hexagonal crimp and then makes a small indent in the same crimp cycle. This secondary indent further improves gas tightness and well as the electrical and mechanical properties of the crimp connection. |
|
 |
 |
 |
 |
|
DV1300 Dual Crimp head
- Dual dies are available for 16 - 300 mm²
- No Die holders are necessary when using DUAL dies.
- Conventional dies for the DV1300 can be used without the dual function.
- The DV1300 can also be used with regular crimp dies for the 1300 system.
- Can be used with foot pump or battery / mains powered pump.
|
|
DV1300C Dual Crimp head
- Dual dies are available for 16 - 300 mm²
- No Die holders are necessary when using DUAL dies.
- Conventional dies for the DV1300C can be used without the dual function.
- The DV1300C can also be used with regular crimp dies for the 1300C system.
- Can be used with footpump or battery / mains powered pump
|
|
| Back to Top |
|
| Copyright Tranect ©2009. Site design by Webwizards. All rights reserved. |
|
